![]() Developer Suite 2013 DS1 has LabVIEW 2012 SP1. Developer Suite 2012 DS2 will LabVIEW 2012. ![]() Developer Suite 2012 DS1 has LabVIEW 2011 SP1. The version of LabVIEW is not directly related to the Developer Suite version. After the reinstallation, only LabVIEW 2011 SP1 was installed and 2012 DS1 was not. I did a complete uninstall and then reinstall of LabVIEW (32 bit). When I first installed LabVIEW (32 bit) of these disks 2012 DS1 has been installed. OR Developer Suite 2012 DS1 disks to install only 2011 SP1 or you can buy each (IEC 61850, DNP3 and IEC 60870) toolkit separately However, you can buy Electrical Power Suite Pro + amulet of usefulness of the protocols and it has the EPS Pro and IEC 61850 and DNP3.Ĥ. the IEC 61850, DNP3 and IEC 60870 toolkit are not part of the Suite of developer.ģ. the NO-Industrial Communications for EtherNet/IP is included in the Developer Suite, as mentioned JDizzle: Ģ. Is it not the case? How can I check the toolkits are covered and which are not?ġ. The same serial number was accepted for activation of OR-Industrial Communications for Ethernet/IP, so I thought that I would have access to all communication, including IEC 61850 toolboxes. However, I was said, "the following order numbers are not valid or do not correspond to their corresponding products. I downloaded OR-Industrial Communications for IEC 61850 14.0 and tried to activate it using my serial number for NI Developer Suite. Is NEITHER-Industrial Communications for IEC 61850 covered by all NI Developer Suite? But he uses the license even exact 32-bit. The installation program is not included in the disks on Developer. So now, we are not Developer Suite / LabVIEW.ĭon't LabVIEW 64-bit included in Developer suite? Received new drives which read "NI Developer Suite 2010", which is misleading, because it's not LabVIEW 2010, is LabVIEW 2009 SP1. NOR Developer Suite 2010 is not LabVIEW 2010 Yes, you need SSP to make from this link. On the support page for LabVIEW 64-bit vs 32-bit FAQ, it says to download the 64-bit version in the "Windows Setup can be downloaded via the drivers and updates: LabVIEW 64-bit section of our Web site", but the Developer Suite for 2012 64 bit is not listed. We have for LabVIEW NI Developer Suite 2012 32-bit installation DVD. Supported Courses: EE 185/186, CPRE 186, EE 285Ĭircuit Components (resistors, capacitors, wires, leds, mosfets, etc.Where can I download LabVIEW NI Developer Suite 2012 64-bit? ![]() Supported Courses: EE/CPRE 201 & 230, EE 333, EE 423, EE 424įreshman Engineering Lab 2018 ECPE Building Addition ![]() Supported Courses: EE/CPRE 201 and 230, EE 333, EE 423, EE 424Įlectric and Electronic Circuits Lab 2014 ECPE Building Addition ![]() IRobot Create 2 Robots with custom hardware and peripheralsĬommunications and Systems Lab 2011 ECPE Building Addition Supported Courses: CPRE 281, 288, and 381 Supported Courses: Most all 200 and 300 level EE, CPRE, and SE Courses Computers have software to support most labs and classes. There are 12 work benches with all the equipment and software for EE 201, 230, 333 and CPRE 281. This lab was built with the intent of acting as an overflow for our Teaching Labs so students could finish experiments if they did not have time in their lab. Supported Courses: EE 491, EE 492 Transformative Learning Area 1313 Coover Hall All the lab machines have software available to the COE and any other one off software that is required for projects. It has multiple toolboxes, test equipment, test equipment, specialty tools, etc. This lab supports our 2 semester Senior Design Program. Supported Courses: EE 303, EE 456, EE 457 Advanced Interactive Classroom 1041 ECpE Building Addition Having trouble in a lab? Submit a support request or stop by in 1331 Coover Hall to visit ETG. The Department of Electrical and Computer Engineering houses several computer labs for students to use. ![]()
0 Comments
Leave a Reply. |